Layout of the Paper

Section A: 4 short questions on the Core topics, 20 marks per question, marked out of your best 3. Attempt all four.

Section B: 3 long questions on the Core topics. 45 marks per question, marked out of your best two. Read all three, do the two you are most confident on, if you have time at the end of the exam then attempt the third.

Section C: This section has 5 optional areas on Applied Graphics but you will only be marked on two of these. The areas covered are Structural Forms and Geological Geometry. Do not waste time attempting another question in this section.

The exam is 3 hours long which allows for around 35 minutes for each of the long questions and another 35 minutes for all of the short questions in Section A.

Make sure your sets are fully equiped before the exam.

Core Topics

Orthographic and Auxiliary Projection

Most questions on the course are given in an orthographic (ele, plan and end ele). A lot of questions will need to have auxiliaries to solve them. Know how to do first and second auxiliaries. Auxiliaries will be used to get true lengths, dihedral angles, point views, etc. (Page 51-53)

Solids in Contact

Know how to find points of contact in plan and elevation (page 83-84)

How to rotate spheres, cones, cylinders to the side of an object, bring them down and find them in their correct position in plan. (page 85-93)

Tracery - Given two solids that the new object touchs off but not the size of the new object. Use tracery to find the centrepoint. (page 97-102)

Tangent Planes - You will be asked to get the traces of the tangent plane. This is solves by cones. If the plane is lying against the cone (tangential to it) then the plane has to have the same angle as the side of the cone. But the same angled cone over the other solid, get the projections in plan to get the Horizontal Trace and then find the Vertical Trace in elevation (page 103-105).

Axonometric, Dimetric and Trimetric

Set up the axes as given in the question. Draw a level line, project and get the semi circle to allow you to set up the plan. Do similar for elevation or end elevation. Look at the 3D view given in the question to decide which elevation to draw and the direction the plan is drawn. If you get this wrong the object could end up facing in the wrong direction. Circles and curves are got by dividing up 60/30 and projecting the individual points to the middle to get the freehand curve (page 137-151).

Perspective

Gettiing the plan drawn, finding the spectator, picture plane, ground line, horizon line and vanishing points will get you nearly half the marks in this question.

Join outer parts of plan to the spectator, bisect this angle to get the line of vision, go 90° to this through whatever point given in the question to get the picture plane.

Go parallel to the edges of the plan from the spectator till it hits the picture plane and project up 90° to the picture plane to the horizon line to give the vanishing points. 

Heights can only be marked off when its touching off the piture plane. If it doesn't touch the picture plane then you need to continue the line/edge on till it does hit the PP, bring it up and mark the height off on that line, vanish it back to collect the point you were looking for.

Remember that all points have to go be joined from the plan to the spectator and brought up from where that its off the picture plane. 

To get curves in perspective you need to divide up the circle/curve 60/30 and find the points individually (page 169)

Auxiliary Vanishing Points are used for sloping surfaces in perspective (like a roof). The angle is set from the line going from the spectator parrallel to the edge of the plan that was used to get the vanishing points. This will give a height that is used for marking above or below the vanishing point (depending what is needed). (page 174-181)

Conic Sections

Parabola - Eccentricity is equal to one which means the line of ecc. is always 45°.

Ellipse - Eccentricity is less than one so the line of ecc. is any angle less that 45°

Hyperbola - Eccentricity is greater than one so the line of ecc. is any anlgel greater than 45°

 

Eccentricity method is done the same way on all three sections. Ecc = PF/PD (See page 191)

Remember that 45° line from focus to the line of ecc. and straight down from there will give the vertex.

Know how to draw a tangent to a point on the curve and a point outside the curve for all three. (pages 192,194,203,204,214,215)

Double Hyberbola is drawn using a different method (page 211). The transverse axis goes from vertex to vertex. Remember the rule PF1-PF2 = transverse axis.

Learn the properties common to all conics (page 219-221)

Know how to get the centre of curvature for a point. (page 222)

Solids cut by Oblique Plane

Set up the ele and plan. Draw the traces. Project up along the horizontal trace to get an auxiliary view showing the cutting plane. Use this view to find the points needed to finish the plan. (page 234-239) 

Rotate the points from the auxiliary to get the true shap of the cut surface out 90° from the plan. (page 240-241)

Get the traces of a plane by continuing on the edges in both plan and ele to find the traces. (page 243)

Intersecting Planes

The coordinates are given in the sequence in, up, down.

To get the dihedral angle you first need the line of intersection, then look 90° to that to get its true length. Then look along the true length to get the dihedral angle.

To get the line of intersection you may have to take either one or two level lines to get points on that line of intersection. Take the level line in ele so that it goes accross the two planes. Where it intersects the planes, drop the points down and find them in plan. Join them up according to the planes they are on and this will give two lines crossing in plan to give one point on the line of intersection.  (page 254-260)

Skew Lines

This is a follow on from intersecting planes but it only deals with two lines.

To get the line parallel to each other, you take a level line in ele, go parallel to the other line to give a point, drop that down and do the same in plan to give the strike line. This line is the angle of the auxiliary for getting the two lines parallel. (page 261)

At this point a few different things can be asked, shortest horizontal distance, shortest perpendicular distance, etc. (page 261-264)

Interpentration

On basic questions, intersection points can be got by using method like Limits, Radial Elements, Horizontal and Vertical sections. (page 274-283). Questions like these generally tend to come up in the short questions.

Long questions tend to be in the form of auxiliary plan method. Draw what you can of the ele and plan. Project the auxiliary plan by taking distance from the xy line down to points in the plan. Label all the points in all three view. Remember there will be a set of points where the object starts to go into the other and also a set where the object comes out the other side. Take one of these at a time. Point that are not found on the edges may need to have a generator drawn for them in the auxiliary, find that generator in ele and then find the point on that generator. (page 287-288)

Developments

Developments are the opening out of an 3D object to a flat 2D shape. (page 297-304) 

An envelopment is the opposite of a development, given the flat shape and you have to draw the 3D shape. (page 309-329)

Applied Graphics

Structural Forms

This has three main parts, the hyperboloid of revolution, the hyperbolic paraboloid and the surface of translation piece.

Hyperboloid of Revolution - Know how to draw the curve in elevation by drawing the asymptote in plan and ele and finding the points from that (page 215). Know how to draw it if the top has some part cut off it and also if you are asked to get a true shape (page 221)

Hyperbolic Paraboloid - Divide up the edges to get the elements needed. Project these elements to all view and they will produce the curves needed. Know how to take a section view along a line. (page 218-220).

Get the plane director by using the level line method as in intersecting planes. This will give an auxiliary showing the plane director which is when all the elements are parallel to each other. This will also be the angle of the horizontal trace of the plance director if asked that. (page 224-228)

Surface of Translation - This is where a parabola slides down another parabola. It gives a shape that can be called a saddle roof. You need to know how to draw a parabola in a rectangle. Then it is a case of taking heights from the ele, dropping them down from the top of the parabola in end ele to give a width and using that width to give the points in plan. (page 230)

Additions to this is where parts of the piece are cut off or you have to work in reverse to get the curve in ele after taking the width from the plan to get the height needed in end ele. (page 231)

 

Geological Geometry

There are two main topics in this section, road geometry and mining geometry.

Road Geometry - You will have to know how to get cut and fill for a level and sloping road.

If you are cutting then the level of the road is below the contours on the map. If you are filling then the level of the road is above the contours on the map.

For a level road you come out parallel to the side of the road. The distances you come out is determined on wheither you are cutting or filling and what ratios there are for them. The ratio given is always multiplied by the intervals of the ground contours (normally 5m).

For a sloping road you will have to set up a cone (semi-circle) at the edge of the road. It will depend on if you are cutting or filling which part of the road this cone will be placed.

If you are cutting the cone will be on the low side of the road (Cut Low) 

If you are filling the cone will be on the high side of the road (Fill High)

Mining Geometry - Know how to get the dip, strike and thickness the traditional method by using the elevation and the level line method (page 263,270-275)

These can also be found just in the plan by dividing the line between the highest and lowest of the three points. It is divided into the number of intervals there are between these two points. (eg. 80 and 55 have 5 intervals of 5m between them so the line would be divided into 5 parts). The other point is then joined to its corresponding height on the divided line to give the strike line. The dip and thickness are found by looking along this strike line and taking an auxiliary (page 270-275) 

  

 

 

 

Layout of the Paper

Section A: 15 short questions, attempt all questions but you are marked out of best 10.

Section B: 6 long questions, marked out of best 4. Make sure to do at least 4.

35 mins per question for higher level, exam is 3hours long

30 mins per question for ordinary level, exam is 2 and half hours long.

There is no need to put a border on the sheet.

Make sure you put your exam number and not your name on every sheet you hand up.

Remember there are marks going in every question for neatness and accuracy.

Make sure your sets are fully equiped before the exam.

Question 1

Orthographic Projection - Generally have to draw an elevation, plan and end elevation. Plan is always below the elevation. Put end elevation on correct side-looking at the left; see it on the right on your sheet. Make sure to include the hidden detail and to insert the four dimensions.

Question 2

Ellipses - Draw the ellipse using the major and minor circles and then divide it up 60/30. If equal parts are shown then the line has to be divided up into the equal parts(line at an angle, step off parts on your compass, join last back to end of the line and go parallel). If your given 3 points on a curve, join two and bisect, join other two and bisect, where bisectors meet is the centre point.

Question 3

Developments - Draw the elevation, plan and end elevation of the given figure (Only draw what is asked, sometimes not all three are asked for). Do the development separately. Development is where the object is folded out flat. Broken lines are shown wherever there is a fold.

Question 4

Do either Oblique or Isometric

Oblique is where you draw the elevation and come back 45° off it for the depth. Isometric is started by using the crows foot, 30°, 30° and straight up.

Question 5

Transformation Geometry - Remember to label all the points first and read the question to find the correct order and from which points. Translation – Distance and angle, image will looked the same but will have moved position. Axial symmetry - 90° to axial line and rotate points from the line, image will be a mirror of the object. Central symmetry – all the lines go through the central point and rotate around from that point, image will be upside down and back to front.

Question 6

Circles in Contact – Draw what is shown in the question. Circles that touch internally, you take away the radius, circles that touch externally you add the radius. Show all points of contact if asked to in the question.

Short Questions

Main things to watch out for:

Finishing off orthographic – Project lines between the views to finish

Freehand sketching – Reasonable sized sketch, not tiny. Add shade to sketch.

Perspective – Lines have to be vanished to two vanishing points, should look like the given 3D

CAD commands – Learn the command from the hand-out

Scale - Using the given scale to give the measure of the length asked for

Shadow/Shade - Projecting the shadow onto the wall

Area - Give the area by counting all the full squares and all the half squares in given figure

Ellipses - Tangents to ellipses, finding focal points

Area Conversion – Triangle to rectangle, Rectangle to square, Rectangle to triangle

Circles in Contact – Join the centres to get Points of contact; don’t forget ones between circle and line

Developments – Where shape is opened out flat

Layout of the Paper

Section A: 15 short questions, attempt all questions but you are marked out of best 10.

Section B: 6 long questions, marked out of best 4. Make sure to do at least 4.

35 mins per question for higher level, exam is 3hours long

30 mins per question for ordinary level, exam is 2 and half hours long.

There is no need to put a border on the sheet.

Make sure you put your exam number and not your name on every sheet you hand up.

Remember there are marks going in every question for neatness and accuracy.

Make sure your sets are fully equiped before the exam.

Question 1

Orthographic Projection-Generally have to draw an elevation, plan and end elevation. Plan is always below the elevation. Put end elevation on correct side-looking at the left; see it on the right on your sheet. Circle in one view, divide up 60/30, bring to angled line in other view and both to the last view to give freehand curve. True shape by rotating line in plan and bringing up to elevation or by doing an auxiliary elevation from the line in plan.

Question 2

Rotations – Draw the given figure. Bring the point to the line, rotate them to the broken line and project them to the new view that’s asked for. This question may have polygons or enlargements as part of its set up.

Question 3

Axonometric – Set up the axes and draw the given views using the semi-circle method. Lines come up from plan and in at 30° from the other view to give 3D view in the middle. Curves have to be divided 60/30 and each point found individually.

Isometric Scale – Draw the same as isometric except that all measurements given have to be scaled down first. Scale is a 45° and 30° line; real measurements put on 45° line and scaled taken off 30° line.

Question 4

Developments – Draw the given figure and do development separately. Broken lines for folds in development.

Solids in Contact - This question can also have solids in contact as part or all of it. For these,roll the new object out to the side in elevation to see its point of contact. Then bring it down to plan and swing it around to it's proper position there. Sometimes an auxiliary elevation may be needed to find the point of contact. Remember to show all points of contact on the question in all views.

Question 5

Transformation Geometry - Remember to label all the points first and read the question to find the correct order and from which points. Translation – Distance and angle, image will looked the same but will have moved position. Axial symmetry - 90° to axial line and rotate points from the line, image will be a mirror of the object. Central symmetry – all the lines go through the central point and rotate around from that point, image will be upside down and back to front. Rotation – Set up the triangle for the angle given to get the rotation point. Rotate from this point, join each point to the rotation point and set off the angle to get the new point, image will have rotated around by the given angle.

Question 6

Ellipses and Parabolas – Parabola is drawn in a rectangle, take note of where the vertex is as that is where the angled lines join to. Ellipse is drawn using concentric circles method. Other things needed may be; Half the major swung from minor gives focal point, Focal point to point on curve plus point to other focal point is length of major axis. Know how to find the major circle when given the minor and a point on the curve (sketch it out). Know how to get a portion of a given ellipse. Know how to get an tangent to a point on the curve and a tangent to a point outside the curve.

Short Questions

Main things to watch out for:

Finishing off orthographic – Project lines between the views to finish

Freehand sketching – Reasonable sized sketch, not tiny. Add shade to sketch.

Perspective – Lines have to be vanished to two vanishing points, should look like the given 3D

Enlargements – From point A through the point and extend to meet the line.

CAD commands – Learn the command from the hand-out

Area Conversion – Triangle to rectangle, Rectangle to square, Rectangle to triangle

Circles in Contact – Join the centres to get Points of contact; don’t forget ones between circle and line

Developments – Where shape is opened out flat

Auxiliaries - 90° to X1Y1 from plan and take heights from elevation

Design and Communication Graphics

The following images are some examples of pages from previous DCG projects done by Leaving Cert students in GCS.

 

  • 1